Igneus Life Science

These compact tube furnaces with SiC rod heating and integrated switchgear and controller can be used universally for many processes. With an easy to replace working tube as well as additional standard equipment options, these furnaces are flexible and can be used for a wide range of applications. The high-quality fiber insulation ensures fast heating and cooling times. The SiC heating rods installed parallel to the working tube ensure excellent temperature uniformity. The price-performance ratio for this temperature range is unbeatable.

• Tmax 1500 °C
• Dual shell housing made of sheets of textured stainless steel
• Only fiber materials are used which are not classified as carcinogenic according to TRGS 905, class 1 or 2
• Active cooling of housing for low surface temperatures
• Type S thermocouple
• Solid state relays provide for low-noise operation
• Prepared for assembly of working tubes with water-cooled flanges
• Ceramic tube, C 799 quality
• Defined application within the constraints of the operating instructions
• NTLog Basic for Nabertherm controller: recording of process data with USB-flash drive

• Over-temperature limiter with adjustable cutout temperature for thermal protection class 2 in accordance with EN 60519-2 as temperature limiter to protect the furnace and load
• Charge control with temperature measurement in the working tube and in the furnace chamber outside the tube
• Fiber plugs
• Check valve at gas outlet avoids intrusion of false air
• Working tubes for operation with water-cooled flanges
• Display of inner tube temperature with additional thermocouple
• Alternative gas supply systems for protective gas or vacuum operation
• Process control and documentation via VCD software package for monitoring, documentation and control

The high-temperature tube furnaces are available in either horizontal (type RHTH) or vertical (type RHTV) designs. High-quality insulation materials made of vacuum-formed fiber plates enable energy-saving operation and a fast heating time due to low heat storage and heat conductivity. By using different gas supply systems, operations can be performed under non-flammable or flammable protective or reactive gases or under vacuum.

Other Detail:

• Tmax 1600 °C, 1700 °C, or 1800 °C
• MoSi₂ heating elements, mounted vertically for easy replacement
• Insulation with vacuum-formed ceramic fiber plates
• Only fiber materials are used which are not classified as carcinogenic according to TRGS 905, class 1 or 2
• Rectangular outer housing with slots for convection cooling
• Tube furnaces RHTV with frame for vertical operation
• Dual shell housing made of sheets of textured stainless steel
• Ceramic working tube made of material C 799 incl. fiber plugs for operation under air
• Type B thermocouple
• Power unit with low-voltage transformer and thyristor
• Over-temperature limiter with adjustable cutout temperature for thermal protection class 2 in accordance with EN 60519-2 as temperature limiter to protect the furnace and load and with selectable maximum temperature gradient as tube protection
• Switchgear and control unit separate from furnace in separate floor standing cabinet
• Defined application within the constraints of the operating instructions
• NTLog Basic for Nabertherm controller: recording of process data with USB-flash drive

• Charge control with temperature measurement in the working tube and in the furnace chamber outside the tube
• Display of inner tube temperature with additional thermocouple
• Gas tight flanges for protective gas and vacuum operation
• Manual or automatic gas supply system
• Three-zone control for optimization of temperature uniformity (only tube furnaces RHTH)
• Check valve at gas outlet avoids intrusion of false air
• Process control and documentation via VCD software package or Nabertherm Control Center (NCC) for monitoring, documentation and control.

The ashing furnaces LV 3/11 - LVT 15/11 are especially designed for ashing in the laboratory. A special air intake and exhaust system allows air exchange of more than 6 times per minute. Incoming air is preheated to ensure a good temperature uniformity.

• Heating from two sides
• Ceramic heating plates with integral heating element which is safeguarded against fumes and splashing, and easy to replace
• Air exchange of more than 6 times per minute
• Good temperature uniformity due to preheating of incoming air
• Only fiber materials are used which are not classified as carcinogenic according to TRGS 905, class 1 or 2
• Housing made of sheets of textured stainless steel
• Dual shell housing for low external temperatures and stability
• Optional flap door (LV) which can be used as work platform or lift door (LVT) with hot surface facing away from the operator
• Solid state relays provide for low­noise operation
• Defined application within the constraints of the operating instructions
• NTLog Basic for Nabertherm controller: recording of process data with USB-flash drive

• Over-temperature limiter with adjustable cutout temperature for thermal protection class 2 in accordance with EN 60519-2 as temperature limiter to protect the furnace and load
• Observation hole in the door
• Process control and documentation via VCD software package for monitoring, documentation and control

The ashing furnace L 40/11 BO is specially designed for processes in which larger sample quantities have to be incinerated. Fields of application are e.g. the ashing of food, thermal cleaning of injection molding tools or the determination of annealing loss. Another application is the debinding of ceramic products, e.g. after additive production.

The ashing furnaces have a passive safety system and integrated exhaust gas post combustion. An exhaust gas fan extracts flue gases from the furnace and simultaneously supplies fresh air to the furnace atmosphere with the result that sufficient oxygen is always available for the incineration process. The incoming air is guided behind the furnace heating and preheated to ensure good temperature uniformity. Exhaust gases are led from the furnace chamber to the integrated post combustion system, where they are postburned and catalytically cleaned. Directly after the incineration process (up to max. 600 °C) a subsequent process up to max. 1100 °C can take place.

• Tmax 600 °C for the incineration process
• Tmax 1100 °C for the subsequent process
• Three-side heating (both sides and bottom)
• Ceramic heating plates with embedded heating wire
• Only fiber materials are used which are not classified as carcinogenic according to TRGS 905, class 1 or 2
• Dual shell housing made of structured stainless steel provides for low outer temperature and high stability
• Steel collecting pan protects the bottom insulation
• Spring-assisted closing of the furnace door (flap door) with mechanical locking against unintentional opening
• Thermal/catalytic post combustion, integrated in the exhaust channel, up to 600 °C in function
• Temperature control of post combustion can be set up to 850 °C
• Monitored exhaust air
• Inlet-air preheated through the bottom heating plate
• Over-temperature limiter with adjustable cutout temperature for thermal protection class 2 in accordance with EN 60519-2 as temperature limiter to protect the furnace and load
• Defined application within the constraints of the operating instructions
• NTLog Basic for Nabertherm controller: recording of process data with USB-flash drive

• Process control and documentation via VCD software package for monitoring, documentation and control

These models stand out for their excellent workmanship, advanced and attractive design, and high level of reliability. Heating elements on support tubes radiating freely into the furnace chamber provide for particularly short heating times and a maximum temperature of 1400 °C. These muffle furnaces are a good alternative to the familiar L(T) 9/11 SW when higher application temperatures are needed.

• Tmax 1400 °C
• Heating from two sides
• Heating elements on support tubes ensure free heat radiation and a long service life
• Only fiber materials are used which are not classified as carcinogenic according to TRGS 905, class 1 or 2
• Dual shell housing for low external temperatures and high stability
• Adjustable air inlet integrated in door
• Exhaust air outlet in rear wall of furnace
• Solid state relays provide for low-noise operation
• Defined application within the constraints of the operating instructions
• NTLog Basic for Nabertherm controller: recording of process data with USB-flash drive

• Chimney, chimney with fan or catalytic converter
• Over-temperature limiter with adjustable cutout temperature for thermal protection class 2 in accordance with EN 60519-2 as temperature limiter to protect the furnace and load
• Protective gas connection to purge with non-flammable protective or reaction gases (not available in combination with chimney, chimney with fan or catalytic converter)
• Manual or automatic gas supply system
• Process control and documentation via VCD software package for monitoring, documentation and control

We particularly recommend the muffle furnace L 9/11/SKM if your application involves aggressive substances. The furnace has a ceramic muffle with embedded heating from four sides. The muffle furnace thus combines a very good temperature uniformity with excellent protection of the heating elements from aggressive atmospheres. Another aspect is the smooth, nearly particle free muffle (furnace door made of fiber insulation), an important quality feature for some ashing processes.

• Muffle heated from four sides
• Furnace chamber with embedded ceramic muffle, high resistance to aggressive gasses and vapours
• Dual shell housing made of sheets of textured stainless steel
• Only fiber materials are used which are not classified as carcinogenic according to TRGS 905, class 1 or 2
• Optional flap door (L) which can be used as work platform or lift door (LT) with hot surface facing away from the operator
• Adjustable working air inlet in the door
• Exhaust air outlet in rear wall of furnace
• Solid state relays provide for low­noise operation
• Defined application within the constraints of the operating instructions
• NTLog Basic for Nabertherm controller: recording of process data with USB-flash drive

• Chimney, chimney with fan or catalytic converter
• Over-temperature limiter with adjustable cutout temperature for thermal protection class 2 in accordance with EN 60519-2 as temperature limiter to protect the furnace and load
• Protective gas connection to purge with non-flammable protective or reaction gases
• Manual or automation gas supply system
• Observation hole in the door
• Process control and documentation via VCD software package for monitoring, documentation and control

These compact tube furnaces are used when laboratory experiments must be performed horizontally, vertically, or at specific angles. The ability to configure the angle of tilt and the working height, and their compact design, also make these tube furnaces suitable for integration into existing process systems.

• Tmax 1100 °C, 1300 °C, or 1500 °C
• Compact design
• Only fiber materials are used which are not classified as carcinogenic according to TRGS 905, class 1 or 2
• Vertical or horizontal operation freely adjustable
• Working height freely adjustable
• Working tube made of C 530 ceramic
• Type S thermocouple
• Operation also possible separate from stand if safety guidelines are observed
• Control system integrated in furnace base
• Defined application within the constraints of the operating instructions
• NTLog Basic for Nabertherm controller: recording of process data with USB-flash drive.

These tube furnaces can be used for horizontal or vertical operation. The split-type design makes it easy to change the working tube. It allows for a comfortable exchange of various working tubes (e.g. working tubes made of different materials).

Using the wide range of accessories these professional tube furnaces can be optimally tailored to your process. By upgrading the furnaces with different gas supply systems the operation in a protective gas atmosphere, under vacuum or under flammable protective or reactive gases is possible. Besides convenient standard controllers for process control modern PLC control systems are also available.

• Tmax 1100 °C or 1300 °C
• Dual shell housing made of sheets of textured stainless steel
• Only fiber materials are used which are not classified as carcinogenic according to TRGS 905, class 1 or 2
• Tmax 1100 °C: Type N thermocouple
• Tmax 1300 °C: Type S thermocouple
• Frame for vertical operation (RSV)
• Split-type design for simple insertion of the working tube
• Working tube made of material C 530 incl. fiber plugs for operation under air in scope of delivery
• Heating elements on support tubes provide for free radiation
• RSV: switchgear and control unit separate from furnace in own wall or standing cabinet
• RSH: switchgear and control unit integrated in furnace housing
• Defined application within the constraints of the operating instructions
• NTLog Basic for Nabertherm controller: recording of process data with USB-flash drive

• Charge control with temperature measurement in the working tube and in the furnace chamber outside the tube
• Display of inner tube temperature with additional thermocouple
• Different gas supply systems for non-flammable or flammable protective or reactive gases and vacuum operation
• Three-zone control for optimization of temperature uniformity
• Cooling systems for accelerated cooling of the working tube and charge
• Check valve at gas outlet avoids intrusion of false air
• Base frame with integrated switchgear and controller
• Process control and documentation via VCD software package or Nabertherm Control Center (NCC) for monitoring, documentation and control.

The rotary tube furnaces of the RSRB series are ideally suited for batch operation. The permanent rotation of the working tube ensures that the charge is constantly in motion. Due to the special shape of the quartz reactor with the tapered pipe ends the batch is kept in the rotary tube furnace and can be heat-treated an arbitrarily long time period time; a controlled heating to the temperature profiles is also possible.

• Tmax 1100 °C
• Thermocouple type K
• Dual shell housing made of sheets of textured stainless steel
• Only fiber materials are used which are not classified as carcinogenic according to TRGS 905, class 1 or 2
• Tube furnace designed as table-top model with quartz glass reactor which opens on both sides, tapered ends
• Reactor is removed for emptying out of the rotary tube furnace. Beltless drive and hinged furnace housing (opening temperature < 180 °C) provide for very easy removal through
• Adjustable drive of approx. 2-45 rpm
• Switchgear and control unit separate from tube furnace in own wall or standing cabinet
• Defined application within the constraints of the operating instructions
• NTLog Basic for Nabertherm controller: recording of process data with USB-flash drive

• Three-zone control for the optimization of temperature uniformity
• Temperature display unit in the working tube with measurement by means of an additional thermocouple
• Charge control by means of an additional thermocouple in the working tube
• Different gassing ensures good flushing of the charge with process gas through inlet on one side and outlet on other side of tube
• Gas-tight rotary feedthrough for connection of the rotating reactor to a gas supply system
• Check valve at gas outlet avoids intrusion of false air
• Vacuum design, up to 10^-2 mbar depending on the applied pump
• Open on both sides reactor made of quartz glass with knobs for better mixing of the charge in the tube
• Package for improved charging and discharging of the working tube in the following design.
• Mixing reactor made of quartz glass with integrated blade for better mixing of the batch, closed on one side, large opening on the other side
• Tilting mechanism to the left/to the right. For charging and heat treatment, the furnace is tilted towards the right side until the stop so that the load is charged into the rotary tube furnace. For discharge, the furnace is tilted towards the other side to discharge the powder from the reactor. It is no longer necessary to remove the reactor.
• Rotary tube furnace assembled on base with integrated switchgear and controller, incl. transport casters
• Process control and documentation via VCD software package or Nabertherm Control Center (NCC) for monitoring, documentation and control

The RSRC rotary tube furnaces are particularly suitable for processes where continuously running batch material is heated for a short time.

The rotary tube furnace is positioned slightly inclined heated-up to the target temperature. The material is then continuously supplied at the upper end of the tube. It passes through the heated area of the tube and falls on the lower end out of the tube. The time of heat treatment results from the inclination angle, the rotational speed and the length of the working tube, as well as from the flow properties of the batch material.

Equipped with the optional closed loading system for 5 liter charge material incl. receptacle, the rotary tube furnace can also be used for processes under protective gas or vacuum.

• Tmax 1100 Deg C: Working tube made of quartz glass open at both sides Thermocouple type K.
• Tmax 1300 °C Open tube made of ceramics C 530 Thermocouple type S
• Heating elements on support tubes provide for free radiation
• Dual shell housing made of sheets of textured stainless steel
• Only fiber materials are used which are not classified as carcinogenic according to TRGS 905, class 1 or 2
• Adjustable drive of approx. 2-45 rpm
• Digital display unit for the tilting angle of the rotary tube furnace
• Beltless drive and split-type furnace housing (opening temperature < 180 °C) provide for very easy tube removal
• Compact system, rotary tube furnace positioned on a base frame with Manual spindle drive with crank to preset the tilting angle Switchgear and controls integrated Castors.
• Defined application within the constraints of the operating instructions
• NTLog Basic for Nabertherm controller: recording of process data with USB-flash drive

• Three-zone control for the optimization of temperature uniformity
• Temperature display unit in the working tube with measurement by means of an additional thermocouple
• Charge control by means of an additional thermocouple in the working tube
• Different gassing systems with good flushing of the charge with process gas (also possible with hydrogen) in counterflow (only in combination with feeding system below)
• Vacuum design, up to 10^-2 mbar depending on the applied pump
• Vibrating channel and extension piece on the rotary tube for convenient material supply/removal, suitable for processes in normal atmosphere
• Charging system for continuous material transport, consisting of Collecting bottle made of laboratory glass at the outlet of the working tube Suitable for operation in gas atmosphere or vacuum.
•  Working tubes made of differents materials.
• Quartz glass batch reactors, Tmax 1100 °C
• Higher temperatures up to 1500  °C available on request
• PLC controls for temperature control and the control of connected aggregates such as gearshift and speed of the screw-conveyor, speed of the working tube, switching of the vibration generator, etc.
• Process control and documentation via VCD software package or Nabertherm Control Center (NCC) for monitoring, documentation and control

The RD tube furnaces convince with their unbeatable price-performance ratio, very compact outer dimensions and their low weight. These all-rounders are equipped with a working tube which also serves as support for the heating wires. Thus, the working tube is part of the furnace heating which has the advantage that the furnaces achieve very high heat-up rates. The tube furnaces can be supplied for 1100 °C or 1300 °C. Both models are designed for horizontal application. If the customer requires protective gas atmosphere, a separate working tube incl. gas supply system 1, e.g. made of quartz glass, must be inserted in the working tube.

Other Detail:

• Tmax 1100 °C or 1300 °C
• Dual shell housing made of sheets of textured stainless steel
• Only fiber materials are used which are not classified as carcinogenic according to TRGS 905, class 1 or 2
• Inner diameter of the tube: 30 mm, heated length: 200 mm
• Working tube made of C 530 material including two fiber plugs as standard
• Thermocouple type K (1100 °C) or type S (1300 °C)
• Solid state relays provide for low-noise operation of the heating
• Heating wires wound directly around the working tube resulting in very fast heat-up rates
• Defined application within the constraints of the operating instructions

• Over-temperature limiter with adjustable cutout temperature for thermal protection class 2 in accordance with EN 60519-2 as temperature limiter to protect the furnace and load
• Gas supply system for non-flammable protective or reactive gas

These gas tight retort furnaces are equipped with direct or indirect heating depending on temperature. They are perfectly suited for various heat treatment processes requiring a defined protective or a reaction gas atmosphere. These compact models can also be laid out for heat treatment under vacuum up to 600 °C. The furnace chamber consists of a gas tight retort with water cooling around the door to protect the special sealing. With the corresponding safety technology, retort furnaces are also suitable for applications under reaction gases, such as hydrogen or, in combination with the IDB package, for inert debinding or for pyrolysis processes.

Sealed forced convection chamber furnaces are suitable if a heat treatment process up to 650 °C requires a protective gas atmosphere that does not have to be completely oxygen free. The difference between the two variants is that the I-model only has a sealed outer housing while the SI-model has a welded inner box, which further reduces the residual oxygen concentration.

• Tmax 450 °C and 650 °C
• Silicone door seal
• Furnace housing sealed with silicone
• Protective gas connection in the back wall
• Defined application within the constraints of the operating instructions
• Residual oxygen concentration < 1 % depending on the volume and type of protective gas
• For non-flammable protective and reaction gases such as argon, nitrogen, and forming gas (national regulations must be considered)

• Tmax 650 °C
• Welded inner housing
• 2-sided heating and air circulation
• Door sealed with seal gas
• Sealed connection to circulation motor
• Gas inlet via circulator shaft
• Defined application within the constraints of the operating instructions
• Residual oxygen concentration to 0.1 % depending on the volume and type of protective gas
• For non-flammable protective and reaction gases such as argon, nitrogen, and forming gas (national regulations must be considered)

The muffle furnaces are the right choice for daily laboratory use. These models stand out for their excellent workmanship, advanced and attractive design, and high level of reliability. The muffle furnaces come equipped with either a flap door or lift door at no extra charge.

• Ceramic heating plates with integral heating element which is safeguarded against fumes and splashing, and easy to replace
• Only fiber materials are used which are not classified as carcinogenic according to TRGS 905, class 1 or 2
• Housing made of sheets of textured stainless steel
• Dual shell housing for low external temperatures and high stability
• Optional flap door (L) which can be used as work platform or lift door (LT) with hot surface facing away from the operator
• Adjustable air inlet integrated in door (see illustration)
• Exhaust air outlet in rear wall of furnace
• Solid state relays provide for low-noise operation
• Defined application within the constraints of the operating instructions
• NTLog Basic for Nabertherm controller: recording of process data with USB-flash drive

• Chimney, chimney with fan or catalytic converter (not for L 1)
• Over-temperature limiter with adjustable cutout temperature for thermal protection class 2 in accordance with EN 60519-2 as temperature limiter to protect the furnace and load
• Protective gas connection to purge with non-flammable protective or reaction gases (not available in combination with chimney, chimney with fan or catalytic converter)
• Observation hole in the door
• Manual or automatic gas supply system
• Process control and documentation via VCD software package for monitoring, documentation and control

These furnaces are especially used for the assay of precious metals and ashing processes where the insulation and heating must be protected from emerging gasses and vapours. The furnace chamber forms a ceramic muffle which can easily be replaced. The assay furnace is equipped with an integrated exhaust hood above the furnace door for connection to and exhaust sytem.

• Muffle heated from four sides (three sides for assay furnace N 25/13 CUP)
• Heating elements and insulation protected by muffle
• Simple replacement of muffle
• Only fiber materials are used which are not classified as carcinogenic according to TRGS 905, class 1 or 2
• Warm furnace can be opened
• Tool holder on furnace
• Stainless steel exhaust chimney above the door opening for connection of an exhaust system
• Dual shell housing with fan cooling to reduce exterior temperatures
• Defined application within the constraints of the operating instructions
• NTLog Basic for Nabertherm controller: recording of process data with USB-flash drive

• Base frame on castors (not for assay furnace N 4/13 CUP)
• Process control and documentation via VCD software package for monitoring, documentation and control

• For bigger charges we offer pit-type furnaces as assay furnace

To withstand harsh use in the laboratory, e.g. when heat-treating metals, robust insulation with light refractory bricks is necessary. The chamber furnaces N 7/H - N 87/H are a perfect fit to solve this problem. The furnaces can be extended with a variety of accessories, like annealing boxes for operation under protective gas, roller guides, or a cooling station with a quench tank. Even high-performance applications like the annealing of titanium in medical applications can be implemented without the use of expensive and complicated annealing systems.

• Tmax 1280 °C
• Deep furnace chamber with three-sides heating: from both side walls and bottom
• Heating elements on support tubes ensure free heat radiation and a long service life
• Bottom heating protected by heat-resistant SiC plate
• Low energy consumption due to multi-layer insulation
• Exhaust opening in the side of the furnace, or on back wall of chamber furnace N 31/H and higher
• Base frame included in the delivery, N 7/H - N 17/HR designed as table-top model
• Parallel guided downward swinging door (user protected from heat radiation)
• Gas spring dampers provide for easy door opening and closing
• Defined application within the constraints of the operating instructions
• NTLog Basic for Nabertherm controller: recording of process data with USB-flash drive

These chamber furnaces with air circulation are characterized by their extremely high temperature uniformity. Hence, they are especially suitable for processes such as cooling, crystalizing, preheating, curing, but also for numerous processes in tool making. Due to the modular concept, the forced convection furnaces can be adjusted to the process requirements by adding suitable equipment.

• Tmax 450 °C, 650 °C, or 850 °C
• Horizontal air circulation
• Swing door hinged on the right
• Temperature uniformity up to +/- 4 °C according to DIN 17052-1 (model NA 15/65 up to +/- 5 °C)
• Optimum air flow and temperature uniformity through high circulation rates
• One frame sheet and rails for two additional trays included in the scope of delivery (NA 15/65 without frame sheet)
• Stainless steel air-baffles in the furnace for optimum air circulation
• Base frame included in the delivery, NA 15/65 designed as table-top model
• Air inlet and exhaust air flaps as additional equipment for using as drying oven
• Defined application within the constraints of the operating instructions
• NTLog Basic for Nabertherm controller: recording of process data with USB-flash drive

With their maximum working temperature of up to 300 °C and air circulation, the ovens achieve a perfect temperature uniformity which is much better than in ovens of most competitors. They can be used for various applications such as e.g. drying, sterilizing or warm storing. Ample warehousing of standard models provides for short delivery times.

• Tmax 300 °C
• Working temperature range: + 5 °C above room temperature up to 300 °C
• Ovens TR 30 - TR 240 designed as tabletop models
• Ovens TR 450 and TR 1050 designed as floor standing models
• Horizontal, air circulation results in temperature uniformity better than +/- 5 °C
• Stainless steel chamber, alloy 304 (AISI)/(DIN material no. 1.4301), rust-resistant and easy to clean
• Only fiber materials are used which are not classified as carcinogenic according to TRGS 905, class 1 or 2
• Large handle to open and close the door
• Charging in multiple layers possible using removeable grids (number of removeable grids included, see table to the right)
• Large, wide-opening swing door, hinged on the right with quick release for models TR 30 - TR 450
• Double swing door with quick release for TR 1050
• TR 1050 equipped transport rollers
• Infinitely adjustable exhaust at the rear wall with operation from the front
• PID microprocessor control with self-diagnosis system
• Solid state relays provide for low­noise operation
• Defined application within the constraints of the operating instructions
• NTLog Basic for Nabertherm controller: recording of process data with USB-flash drive

• Over-temperature limiter with adjustable cutout temperature for thermal protection class 2 in accordance with EN 60519-2 as temperature limiter to protect the oven and load
• Infinitely adjustable fan speed of the air circulation fan
• Window for charge observing
• Further removeable grids with rails
• Side inlet
• Stainless steel collecting pan to protect the furnace chamber
• Door hinges on the left side
• Reinforced bottom plate
• Safety technology according to EN 1539 for charges containing liquid solvents (TR .. LS) up to model TR 240 LS, achievable temperature uniformity +/- 8 °C
• Transport castors for model TR 450
• Various modifications available for individual needs
• Upgrading available to meet the quality requirements of AMS 2750 E or FDA
• Process control and documentation via VCD software package for monitoring, documentation and control

These compact melting furnaces for the melting of non-ferrous metals and alloys are one of a kind and have a number of technical advantages. Designed as tabletop models, they can be used for many laboratory applications. The practical counter balanced hinge with shock absorbers and the spout (not for KC) on the front of the furnace make exact dosing easy when pouring the melt. The melting furnaces are available for furnace chamber temperatures of 1000, 1300, or 1500 °C. This corresponds to melt temperatures of about 80 °C - 110 °C lower.

• Tmax 1000 °C, 1300 °C, or 1500 °C, with melt temperature about 80 °C - 110 °C lower
• Crucible sizes of 0,75, 1,5 or 3 liters
• Crucible with integrated pouring spout of iso-graphite included with delivery
• Additional spout (not for KC), mounted at the furnace for exact pouring
• Compact bench-top design, simple emptying of crucible by tiltiing system with gas damper
• Crucible for heating up of melting furnace insulated with a hinged lid, lid opened when pouring
• Defined application within the constraints of the operating instructions

• Other crucible types available, e.g. steel
• Design as bale-out furnace without tilting device, e.g. for lead melting
• Over-temperature limiter for the furnace chamber with automatic reset to protect against overtemperature. The limit controller switches off the heating when the pre-set limit temperature has been reached and does not switch it on again until the temperature falls below the setting again.
• Observation hole for melt

These models stand out for their excellent workmanship, advanced and attractive design, and high level of reliability. Heating elements on support tubes radiating freely into the furnace chamber provide for particularly short heating times and a maximum temperature of 1400 °C. These muffle furnaces are a good alternative to the familiar L(T) ../11 series when higher application temperatures are needed.

• Heating from two sides
• Heating elements on support tubes ensure free heat radiation and a long service life
• Only fiber materials are used which are not classified as carcinogenic according to TRGS 905, class 1 or 2
• Dual shell housing for low external temperatures and high stability
• Adjustable air inlet integrated in door
• Exhaust air outlet in rear wall of furnace
• Solid state relays provide for low-noise operation
• Defined application within the constraints of the operating instructions
• NTLog Basic for Nabertherm controller: recording of process data with USB-flash drive

• Chimney, chimney with fan or catalytic converter
• Over-temperature limiter with adjustable cutout temperature for thermal protection class 2 in accordance with EN 60519-2 as temperature limiter to protect the furnace and load
• Protective gas connection to purge with non-flammable protective or reaction gases (not available in combination with chimney, chimney with fan or catalytic converter)
• Manual or automatic gas supply system
• Process control and documentation via VCD software package for monitoring, documentation and control